Skip to content
Set up my rig

Black Myth: Wukong: how to get more FPS and less lag

Practical advice to raise your frame rate and cut lag in Black Myth: Wukong: what limits performance, the settings that cost the most frames, upscaling, how to show FPS and network tips.

DontLag · · updated Nov 12, 2026

Black Myth: Wukong: how to get more FPS and less lag

Black Myth: Wukong is a visually heavy action RPG built on Unreal Engine 5 with optional full ray tracing, so the right preset matters.

What limits performance in Black Myth: Wukong

Black Myth: Wukong is mostly GPU-limited, with the CPU mattering in some areas. VRAM use is high, so match textures to your card. An SSD is recommended for the minimum specs and required for the recommended specs.

The settings that cost the most frames

Start with these, test after each change, and keep the ones that give a clear gain.

  • Full Ray Tracing: Off unless you have a high-end GPU. Without it the game uses Unreal Engine software Lumen, which is much cheaper.
  • Super Resolution: this is a percentage slider (25% to 100%). Around 58% to 75% suits 1440p and 4K; 80% to 100% suits 1080p.
  • Global Illumination Quality and Shadow Quality: Medium or High; Medium at 1080p.
  • Visual Effect Quality and Post Effects Quality: Medium or High.
  • Texture Quality: match to VRAM.
  • Hair Quality: Low or Medium.

Upscaling and frame generation

Set Super Resolution Sampling to DLSS on NVIDIA RTX cards, or FSR 3 or Intel XeSS on other GPUs; Unreal Engine 5 TSR is also listed. The game has no option to switch upscaling off, so the slider is the control. Frame Generation uses DLSS 3 on RTX 40 series cards and FSR 3 on other GPUs, and it must match the chosen upscaler. It is a good fit for this single-player game when your base frame rate is high enough (aim for 45 fps or more). DLSS Ray Reconstruction is not supported.

How to show the FPS counter

I could not confirm an in-game FPS counter. Use the Steam in-game FPS counter (Steam Settings, In Game) or your GPU overlay. The developer also released a separate benchmark tool for testing your settings.

Network and latency tips

This is a single-player game, so network settings are not relevant.

Quick checks that help in any game

Before you spend an hour in the menus, rule out the common system-level causes of low FPS and stutter in Black Myth: Wukong:

  • Update your graphics driver and restart. Game-ready drivers often include fixes for new releases.
  • Set the Windows power plan to Balanced or High performance, and turn on Game Mode.
  • Enable the XMP or EXPO memory profile in your BIOS. Many PCs run RAM below its rated speed, which costs frames in CPU-limited games.
  • Install the game on an SSD, not a hard drive, to avoid hitching when assets stream in.
  • Close browsers, launchers and overlays you do not need. Each one takes CPU time and memory.
  • Watch your temperatures. A CPU or GPU that overheats lowers its clocks, and the result is lower, uneven frame rates.
  • Match the frame cap to your monitor, or use adaptive sync so a steady frame rate does not tear.

How to test a change properly

Change one setting at a time and repeat the same short test, ideally in the same place or mode, while watching both the average and the lowest frame rates. The 1% lows tell you more about smoothness than the average does. If a setting changes the picture a lot but the frame rate barely moves, put it back; if it moves the frame rate a lot and the picture barely changes, keep it lower. Check whether the GPU or CPU is the one running at 95 to 100 percent: lowering resolution-related settings only helps when the GPU is the bottleneck, while lowering view distance, crowd and physics options is what helps when the CPU is.

Best settings for your hardware

Every PC is different, so the best choice depends on your CPU, graphics card and monitor. On DontLag you can find recommended settings for each hardware tier on the Black Myth: Wukong settings page.

Sources

Related guides