Skip to content
Set up my rig

Monster Hunter Wilds: how to get more FPS and less lag

Practical advice to raise your frame rate and cut lag in Monster Hunter Wilds: what limits performance, the settings that cost the most frames, upscaling, how to show FPS and network tips.

DontLag · · updated Nov 12, 2026

Monster Hunter Wilds: how to get more FPS and less lag

Monster Hunter Wilds runs on Capcom's RE Engine and has been one of the more demanding recent games on PC, but a run of patches between December 2025 and February 2026 improved performance, so update first and then tune your settings. Information is for update 1.042.00.03 (October 2026).

What limits performance in Monster Hunter Wilds

Monster Hunter Wilds is both CPU- and GPU-limited, with the CPU mattering in hubs and with large numbers of NPCs. VRAM use is high, so match textures to your card. Steam lists Windows 10 or 11, 16 GB of RAM, an SSD and about 75 GB of space as required, even for the minimum specs. The minimum is a GTX 1660 (6 GB) or RX 5500 XT (8 GB), and the recommended card is an RTX 2060 Super or RX 6600 (8 GB), aiming for 1080p and 60 fps with frame generation on Medium.

Update to the latest version first

Several patches targeted PC performance. The Steam patch of 28 January 2026 cut CPU load from shader warming, fixed an FPS drop around the Support Desk in Base Camp and the Grand Hub, adjusted texture streaming to lower VRAM use, shrank the High Resolution Texture Pack (a re-download of about 31 GB) and added a CPU tab in the Options menu. Update 1.041 in February added further CPU and GPU optimisations, including levels of detail for 3D models. Update 1.042 in August addressed stutter with a frame cap and DLSS enabled, and patch 1.042.00.03 in October fixed crashes on some AMD cards. Capcom recommends NVIDIA driver 581.57 or newer and AMD driver 25.9.1 or newer, and has noted problems with AMD drivers 25.10.2 and higher on certain cards such as the RX 5500 XT and RX 7800 XT.

The settings that cost the most frames

Start with these, test after each change, and keep the ones that give a clear gain.

  • Volumetric Fog: Low or Lowest. It is one of the most expensive settings. Since January 2026 it has five levels instead of two.
  • Shadow Quality: Medium. High uses a lot of VRAM and GPU time.
  • Ambient Occlusion: Medium.
  • Ray Tracing (ray-traced reflections): Off on mid-range GPUs.
  • Texture Quality: match to VRAM. Going over your VRAM causes stutter and blurry textures; on 8 GB cards Medium is the safe choice.
  • Motion Blur and Depth of Field: Off if you prefer a sharper picture and a little extra speed.
  • Texture Filtering: High (16x). It costs almost nothing.
  • CPU tab: if your CPU is the bottleneck in hubs and busy fields, look at the options in the CPU tab that the January patch added.

Upscaling and frame generation

Title Update 2 in June 2025 added DLSS 4 (with the Transformer model) and FSR 4 support on PC, alongside DLSS, FSR 3.1 and XeSS. Upscaling and frame generation are separate settings, so you can mix, for example, DLSS upscaling with FSR frame generation. RTX 50-series owners can use DLSS Multi Frame Generation at 2x, 3x or 4x. Use Quality or Balanced upscaling and avoid native TAA. Frame generation can help in this single-player-focused game, but only when your base frame rate is already around 40 to 60 fps. With DLSS Frame Generation set NVIDIA Reflex to On + Boost; AMD Anti-Lag 2 pairs with FSR 3 Frame Generation.

How to show the FPS counter

Capcom released a free Monster Hunter Wilds Benchmark tool on Steam for testing settings. I could not confirm an in-game FPS counter, so use the Steam in-game FPS counter (Steam Settings, In Game) or your GPU overlay.

Network and latency tips

In multiplayer hunts, use Ethernet and check NAT type. Lag affects hit timing, so avoid playing over unstable Wi-Fi.

Quick checks that help in any game

Before you spend an hour in the menus, rule out the common system-level causes of low FPS and stutter in Monster Hunter Wilds:

  • Update your graphics driver and restart. Game-ready drivers often include fixes for new releases.
  • Set the Windows power plan to Balanced or High performance, and turn on Game Mode.
  • Enable the XMP or EXPO memory profile in your BIOS. Many PCs run RAM below its rated speed, which costs frames in CPU-limited games.
  • Install the game on an SSD, not a hard drive, to avoid hitching when assets stream in.
  • Close browsers, launchers and overlays you do not need. Each one takes CPU time and memory.
  • Watch your temperatures. A CPU or GPU that overheats lowers its clocks, and the result is lower, uneven frame rates.
  • Match the frame cap to your monitor, or use adaptive sync so a steady frame rate does not tear.

How to test a change properly

Change one setting at a time and repeat the same short test, ideally in the same place or mode, while watching both the average and the lowest frame rates. The 1% lows tell you more about smoothness than the average does. If a setting changes the picture a lot but the frame rate barely moves, put it back; if it moves the frame rate a lot and the picture barely changes, keep it lower. Check whether the GPU or CPU is the one running at 95 to 100 percent: lowering resolution-related settings only helps when the GPU is the bottleneck, while lowering view distance, crowd and physics options is what helps when the CPU is.

Best settings for your hardware

Every PC is different, so the best choice depends on your CPU, graphics card and monitor. On DontLag you can find recommended settings for each hardware tier on the Monster Hunter Wilds settings page.

Sources

Related guides