Skip to content
Set up my rig

Rust: how to get more FPS and less lag

Practical advice to raise your frame rate and cut lag in Rust: what limits performance, the settings that cost the most frames, upscaling, how to show FPS and network tips.

DontLag · · updated Nov 12, 2026

Rust: how to get more FPS and less lag

Facepunch's multiplayer survival game on Unity. Very CPU-heavy in bases and on busy servers, with a large draw distance and many foliage and shadow options that decide how smooth it feels.

What limits performance in Rust

Rust runs on Unity (Survival sandbox, 2018). Official and researched system requirements:

  • Minimum: OS Windows 11 64-bit; CPU AMD Ryzen 5 1400 or Intel Core i5-6600; RAM 12 GB; GPU AMD Radeon RX 470, NVIDIA GeForce GTX 1060, Intel Arc A580; DirectX Version 11; Storage 45 GB (SSD highly recommended)
  • Recommended: OS Windows 11 64-bit; CPU AMD Ryzen 7 3700X or Intel Core i7-6700K; RAM 16 GB; GPU AMD Radeon RX 6600 XT, NVIDIA GeForce RTX 3060, Intel Arc B580; DirectX Version 12; Storage 45 GB (SSD required)

The settings that cost the most frames

Menu names and sections below are the ones in the game. Start here, test after each change, and keep the ones that give a clear gain.

Sunlight through pine trees on a Rust forest floor

Dense foliage like this is demanding on frame rate.

  • Resolution (Screen): native resolution, or lower for more frames. Run at your monitor's native resolution and lower the load with Render Scale or DLSS instead.
  • Vsync (Screen): Off. V-Sync adds input lag; use G-Sync/FreeSync with an FPS cap instead.
  • FPS Limit (Screen): Unlimited. Also available as the console command fps.limit. If your FPS is mysteriously stuck, run fps.limit 0 in the F1 console.
  • Render Scale (Graphics): 1.0. 1.0 is full resolution. Lowering it towards 0.5 gains FPS but blurs the image; DLSS looks better than a low Render Scale.
  • Shadow Quality (Graphics): 0 on the Low preset up to 2 on Ultra. Shadows are one of the biggest GPU costs; the step from 1 to 2 is mostly softer edges.
  • Shadow Cascades (Graphics): No Cascades on the Low preset up to Four Cascades on Ultra. Fewer cascades means a cheaper shadow pass at the cost of blurrier distant shadows.
  • Draw Distance (Graphics): 1500 on the Low preset up to 2000 on Ultra. Community guides find about 2000 gives nearly the same visibility as the maximum for a small FPS cost; 1500 is the budget choice.
  • Object Quality (Graphics): 100 on the Low preset up to 200 on Ultra. Detail of buildings and props (a Mesh Quality slider). Guides use 100 to 150 for PvP.
  • Tree Quality (Graphics): 100 on the Low preset up to 200 on Ultra. Tree mesh detail; lower values also let you see through foliage more easily.
  • Water Quality (Graphics): 0. Water effects are decorative and costly; every guide sets them to 0.
  • Ambient Occlusion (Image Effects): Off. Soft contact shadows cost noticeable FPS for a small visual gain.

Smaller options

SettingWhereRecommended
Particle QualityGraphics0 on the Low preset up to 50 on Ultra
Grass ShadowsGraphicsOff
Max GibsOptions0
Motion BlurImage EffectsOff
Depth Of FieldImage EffectsOff

Upscaling and frame generation

Upscalers: DLSS. No frame generation is listed. Latency reduction: NVIDIA Reflex.

  • Nvidia DLSS (Graphics). Options: Off, Nvidia DLSS. NVIDIA RTX cards only. Rust names the modes Max Quality, Balanced, Max Performance and Ultra Performance; Quality here means Max Quality, Performance means Max Performance.
  • Nvidia Reflex Mode (Graphics). Options: Off, On, On + Boost. Lowers system latency on NVIDIA GPUs. Boost raises CPU and GPU usage a little.

How to show the FPS counter

  1. Press Esc and open Settings > Options.
  2. Set "FPS counter" to Basic (FPS) or Advance (FPS plus heap, RAM and optionally ping).
  3. Alternative: join a server, press F1 to open the console and type client_fps (older guides use perf 1). The main menu does not give an accurate reading.

More Rust tips

Remove an accidental FPS limit

  • Join a server and press F1 to open the console.
  • Type fps.limit 0 and press Enter to remove any limit.

Install Rust on an SSD

  • Facepunch lists an SSD as required for the recommended specs and highly recommended for the minimum.
  • A hard drive causes long loading times and stutter when new areas stream in.

Menu options can change between monthly updates; check the Graphics tab if a setting looks different.

Snowy hills with rocks and grass in Rust

Open terrain is easier on the GPU than thick forest.

Leave the GC Buffer on default

  • Open Settings > Experimental.
  • Keep "GC Buffer (MB)" at its default unless you have 32 GB of RAM or more.

Quick checks that help in any game

Before you spend an hour in the menus, rule out the common system-level causes of low FPS and stutter in Rust:

  • Update your graphics driver and restart. Game-ready drivers often include fixes for new releases.
  • Set the Windows power plan to Balanced or High performance, and turn on Game Mode.
  • Enable the XMP or EXPO memory profile in your BIOS. Many PCs run RAM below its rated speed, which costs frames in CPU-limited games.
  • Install the game on an SSD, not a hard drive, to avoid hitching when assets stream in.
  • Close browsers, launchers and overlays you do not need. Each one takes CPU time and memory.
  • Watch your temperatures. A CPU or GPU that overheats lowers its clocks, and the result is lower, uneven frame rates.
  • Match the frame cap to your monitor, or use adaptive sync so a steady frame rate does not tear.

How to test a change properly

Change one setting at a time and repeat the same short test, ideally in the same place or mode, while watching both the average and the lowest frame rates. The 1% lows tell you more about smoothness than the average does. If a setting changes the picture a lot but the frame rate barely moves, put it back; if it moves the frame rate a lot and the picture barely changes, keep it lower. Check whether the GPU or CPU is the one running at 95 to 100 percent: lowering resolution-related settings only helps when the GPU is the bottleneck, while lowering view distance, crowd and physics options is what helps when the CPU is.

Best settings for your hardware

Every PC is different, so the best choice depends on your CPU, graphics card and monitor. On DontLag you can find recommended settings for each hardware tier on the Rust settings page.

Sources

Related guides